Sunday, June 22, 2014

MakerBot Replicator 2x: More Air Prints, custom heat sink

I am increasingly frustrated with the MakerBot Replicator 2x we have at the office. It seems you need to spend twice the amount of time working on it as you get viable prints. After a streak of good luck and reliability, as of late it refuses to complete any kind of medium or large size print job. It'll get part of the way complete, and then stop feeding filament- a classic air print.

I am guessing the problem is because the aluminum block that holds the stainless steel feed throat for the hot ends in place isn't cooled sufficiently. If it gets too warm, the stainless steel feed throat will get too warm, and the filament will soften before it gets to the hot end nozzle and jam. I thought I would attack this problem by creating an improved heat sink and attempt to move more heat away from the aluminum block, and thus attempt to keep the stainless steel feed throat cooler. I also attempted to improve the insulation between the hot ends and the aluminum block.

First, I constructed a heat sink using 1/8" thick copper sheet purchased from Mcmastercarr. I thought the copper would create a improved heat flow path from the aluminum block to both of the fan-cooled heat sinks, as well as increase the total mass of the heat sink. It should also allow improved heat flow from the aluminum block near extruder #1 to extruder #2's heat sink.


Heat sink cut, drilled, and ready to go

Trial fit of stock heat sinks checking for hole alignment

Test fit on drive block

Test fit on drive block
 Next, I wanted to reduce the convective & radiant heat transfer from the hot ends to the drive block by adding some 1/32" thick silicone rubber, also sourced from www.mcmastercarr.com.

Covering all air gaps on the top of the extruder platform

Sheet of self-adhesive rubber cut to fit the bottom of the aluminum hot end block

Adhered to the bottom of the aluminum block

Extruder #2 Re-attached
During this assembly and dissemble, the thermistor / thermocouple for hot end #1 failed. The stock cables are very thin and fragile, so it wasn't much of a surprise. Makerbot actually sent a replacement thermocouple free of charge. The new thermocouple wire is much thicker and appears more durable than the stock cable.

New Makerbot Replicator 2x thermocouple on the left, original on the right. The stock cable used much smaller gage cable. 
Since this is not the first time I've completely disassembled extruder #1's hot end, the stock ceramic / polyimide / insulation hot end insulation was cracked and looking pretty sad. Rather than tape it back together with some kapton tape I ordered a replacement insulation set off of amazon.com from VIRA design.

Mini-Review of the Vira Design Makerbot Replicator 2x upgrade kit, AKA: Upgrade Kit for the Hot End Insulation on Makerbot Replicator 2x-extruder-reprap


  • Shipping: Slow-  took about two weeks- it appears as though they paid for shipping, then make the parts, then shipped them out. 
  • Packaging: Poor- all the parts were tossed in a much-too large box- although since nothing it breakable it didn't matter
  • Instructions: Poor- zero instructions included with the kit, although if you are capable of installing it you'll be able to figure it out
  • Part quality: Good- cast silicone parts are serviceable, but required x-acto knife cleanup of all thru-holes
  • Value: Good - you'll have a hard time producing these parts yourself for much less, let alone the time required to design, create molds, and make the parts. If you need replacement insulation for your hot ends these are a good option. Plus they are completely non-fragile, unlike the stock ceramic insulation. 
Vira Design upgrade kit for Hot End Insulation on Makerbot Replicator 2x Mini-instructions:

1) Use an X-acto knife to clean out all of the thru-holes in the silicone insulation parts.
New rubber insulation on the right., prior to trim
 2) Cut the white insulation to size for the flat end of the aluminum hot end block.

Using aluminum hot end block as pattern to cut white insulation
 3) Cut kapton / polyimide tape to hold the white insulation to the aluminum block
Cut tape using X-acto
 4) Stick white insulation patch to kapton tape
Ready to go
 5) Attach insulation patch to aluminum hot-end block
Attach tape / insulation patch to aluminum hot end block

Insulation in place
 6) Insert hot-end assembly into silicone insulation
Ready to go!
 Next up, loading new thermocouple into hot end block. I put a dab of thermal heat sink compound onto the threads to improve heat conduction and also to prevent the thermocouple threads from seizing in the aluminum block. When I threaded it in I rotated the aluminum block rather than the thermocouple to minimize any stress on the thermocouple wire. I also only tightened it finger tight- no tools used.

Thermal heat sink compound on thermocouple threads

Hot End #1 installed. 
Next up, finish installation and fire it up.


Thermal compound on the interface between the new copper heat sink and the aluminum hot end block

Thermal compound on the back of the aluminum fan cooled heat sinks

Up and running!

So, after all this, you'd expect it runs perfectly..... And the answer is... NO! Very frustrating. It might work slightly better but I'm still getting air prints. So far I've only been trying authentic MakerBot brand natural ABS filament. I'll try using some generic colored ABS filament- I believe it has a higher melt temp, which might help.

14 comments:

  1. You need to buy Davis headrick 3in1 extruder upgrade.

    https://groups.google.com/forum/#!topic/makerbot/SuzXohTGeZs%5B351-375-false%5D

    Never anymore airprints :)

    ReplyDelete
    Replies
    1. Thanks for the tip! I'm running a 3D printed set of hardware that looks similar, but I'm sure an aluminum and PEEK version would be much better.

      Delete
  2. Thanks for posting your process, we're having the exact same trouble and it's certainly helpful to see the lengths you've gone to already. I'm sorry it didn't work out for you, definitely feel your pain. One thing I might suggest, although this won't likely cure many of the things, is that there should be a pair of holes in your copper plate that align with the center hole of each heatsink. I believe that's to allow some air through to cool the drive gear.

    ReplyDelete
    Replies
    1. The center hole is a good idea. I suppose it could be taken even a step further and connect an air jet from a compressed air hose to blow directly on the drive gear to keep it as cool as possible.

      Delete
  3. This comment has been removed by the author.

    ReplyDelete
  4. We offer exclusive collection of the heat thermocouple. You can design nearly any thermocouple, RTD sensor and see a representation of your design with a price for quick turn-a-round and shipping.

    ReplyDelete
  5. Thanks for sharing nice information with us. i like your post and all you share with us is uptodate and quite informative, i would like to bookmark the page so i can come here again to read you, as you have done a wonderful job. amazon sandblasting hood

    ReplyDelete
  6. I gotta favorite this website it seems very helpful . first manufacturing

    ReplyDelete
  7. Thanks for another excellent post. Where else could anybody get that type of info in such an ideal way of writing? In my opinion, my seeking has ended now. 6v deep cycle battery

    ReplyDelete
  8. I am happy to find this post very useful for me, as it contains lot of information. I always prefer to read the quality content and this thing I found in you post. Thanks for sharing. best 720p projector under 200

    ReplyDelete
  9. I am thankful to you for sharing this plethora of useful information. I found this resource utmost beneficial for me. Thanks a lot for hard work. best garden hose to use with pressure washer

    ReplyDelete
  10. Awesome article! I want people to know just how good this information is in your article. It’s interesting, compelling content. Your views are much like my own concerning this subject. Best Tonneau Covers for Truck Reviews

    ReplyDelete
  11. The website is looking bit flashy and it catches the visitors eyes. Design is pretty simple and a good user friendly interface. best computer chair for gaming under 200

    ReplyDelete
  12. I have been impressed after read this because of some quality work and informative thoughts. I just want to say thanks for the writer and wish you all the best for coming! Your exuberance is refreshing. silicone bibs

    ReplyDelete